- Home
- Sale
- Trapezoidal sheet profiles
- Special profiles
- Sandwich elements
- Liner trays
- Corrugated sheets
- Holorib
- Pantile sheets
- Wall panels
- Arched roof
- Cold roof profiles
- Trapezoidal sheets made of steel
- profiles for composite floor slabs
- Types of material
- Types of coatings
- Stringer and waler
- Lightplates
- Domelight
- Formed components
- Standing rebate systems
- Accessoires
- Mounting material
- Service
- Contact
- Imprint
- Sitemap
Trapezoidal sheet profiles
Trapezoidal sheets
trapezoidal sheet made of steel
trapezoidal sheet - use as roof and wall plates
Trapezoidal sheets are often applied for industrial building. The load carrying system is often built of steel. The trapezoidal sheets are applied for different components such as roof covering, wall covering or ceiling lining.
The DIN 18 807 provides general guidelines for the application of trapezoidal profiles such as minimum limit, tolerance indication, corrosion protection and the calculated notation of section and mesurement properties. The light component elements possess top and bottom flanges as well as bars. To improve the load bearing behaviour the flanges or belts sometimes have beadings in longitudinal as well as in transverse direction which are named, depending on the type of moulding, as corrugation, groove or displacement.
trapezoidal sheet - advantages
Due to their light proper weight the trapezoidal sheets are easy to handle. The special construction of the layed on edge sheets allows an augementation of the bearing load. The easy mounting and the rapid construction progress speak in the favour of trapezoidal sheets as construction material.
trapezoidal sheet - place name - warm roof and cold roof
As roof sheet the trapezoidal sheet made of steel lays in positive direction, if the wide belt is fixed outward or rather at the head and the small belt at the bottom. This system of laying is used for assembly of a warm roof, that means that it serves as base for another roof system. If you would like to use the trapezoidal sheet made of steel as cold roof, the sheet lays in negative direction. The small belt is fixed outward or rather at the head (to the weather side) and the wide belt at the bottom. This laying system is used to avoid that the joint of mounting widths lay in the channel flow.
trapezoidal sheet - coatings
trapezoidal sheets made of stell are available in different designs such as coil galvanized, aluzinc and coil galvanized with plastic coating in the layout DU, Polyester, PVDF, Plastisol = HPS 200, Armatec, Armatone with condensation-inhibiting foil or sound absorption coating (as well as geomenbrane) available.
trapezprofile - measurements - technical Data
For optimizing the necessary trapezoidal sheets according to the static requirements the of tables of applied loads are helpful. You distinguish between single-span beam, two-span beam and three-span beam. Having regard to the span width and the superimposed load the appropriate profile with the thickness of sheet could be found out of the tables of applied loads. Using the tables of applied loads is only a pre-measurment which does not replace a structural analysis.
Trapezoidal sheets made of aluminium
trapezoidal sheet - use as roof and wall plates
Trapezoidal sheets are often applied for industrial building. The load carrying system is often built of steel or wood. The trapezoidal sheets are applied for different components such as roof covering, wall covering or ceiling lining.
The DIN 18 807 provides general guidelines for the application of trapezoidal profiles such as minimum limit, tolerance indication, corrosion protection and the calculated notation of section and mesurement properties. The light component elements possess top and bottom flanges as well as bars. To improve the load bearing behaviour the flanges or belts sometimes have beadings in longitudinal as well as in transverse direction which are named, depending on the type of moulding, as corrugation, groove or displacement.
trapezoidal sheet - advantages
Due to their light proper weight the trapezoidal sheets are easy to handle. The special construction of the layed on edge sheets allows an augementation of the bearing load. The easy mounting and the rapid construction progress speak in the favour of trapezoidal sheets as construction material.
trapezoidal sheet - place name - cold roof
As roof sheet the trapezoidal sheet made of aluminium lays in positive direction, if the small belt is outward or rather on the top and the wide belt is fixed on the bottom. This system of laying is used for assembly of a cold roof.
trapezoidal sheet - designs and coatings
trapezoidal sheets made of aluminium in design alu blanc, alustucco, alu plane. As layouts plastic coatings in Polyester, PVDF with condensation-inhibiting foil or sound absorption coating (as well as geomenbrane) available. Despite of this trapezoidal sheet made of aluminium are also deliverable in anodising quality.
trapezoidal profile - measurement - technical data
For optimizing the necessary trapezoidal sheets according to the static requirements the of tables of applied loads are helpful. You distinguish between single-span beam, two-span beam and three-span beam. Having regard to the span width and the superimposed load the appropriate profile with the thickness of sheet could be found out of the tables of applied loads. Using the tables of applied loads is only a pre-measurment which does not replace a structural analysis.
trapezoidal sheets made of stainless steel
trapezoidal sheet - use as roof and wall plates
Trapezoidal sheets are often applied for industrial building. The load carrying system is often built of steel. The trapezoidal sheets are applied for different components such as roof covering, wall covering or ceiling lining.
The DIN 18 807 provides general guidelines for the application of trapezoidal profiles such as minimum limit, tolerance indication, corrosion protection and the calculated notation of section and mesurement properties. The light component elements possess top and bottom flanges as well as bars. To improve the load bearing behaviour the flanges or belts sometimes have beadings in longitudinal as well as in transverse direction which are named, depending on the type of moulding, as corrugation, groove or displacement.
trapezoidal sheet - advantages
Due to their light proper weight the trapezoidal sheets are easy to handle. The special construction of the layed on edge sheets allows an augementation of the bearing load. The easy mounting and the rapid construction progress speak in the favour of trapezoidal sheets as construction material. Trapezoidal sheets made of stainless steel are often used in food industry, in chemical section or for offshore wind energy plants at sea. Stainless steel is deliverable in general in the qualities 1.4301. 1.4401 (both only in 2B-finish) and aditionally in UGIBRIGHT® in quality 1.4526. All these qualities are furnished with a protection foil on both sides and comply with the European Standard EN 10088-2 and EN 10259.
trapezoidal sheet - place name - warm roof and cold roof
As roof sheet the trapezoidal sheet made of stainless steel lays in positive direction, if the wide belt is fixed outward or rather at the head and the small belt at the bottom. This system of laying is used for assembly of a warm roof, that means that it serves as base for another roof system. If you would like to use the trapezoidal sheet made of steel as cold roof, the sheet lays in negative direction. The small belt is fixed outward or rather at the head (to the weather side) and the wide belt at the bottom. This laying system is used to avoid that the joint of mounting widths lay in the channel flow.
trapezoidal sheet - coatings
trapezoidal sheets made of stell are available in different designs such as coil galvanized, aluzinc and coil galvanized with plastic coating in the layout DU, Polyester, PVDF, Plastisol = HPS 200, Armatec, Armatone with condensation-inhibiting foil or sound absorption coating (as well as geomenbrane) available.
trapezprofile - measurements - technical Data
For optimizing the necessary trapezoidal sheets according to the static requirements the of tables of applied loads are helpful. You distinguish between single-span beam, two-span beam and three-span beam. Having regard to the span width and the superimposed load the appropriate profile with the thickness of sheet could be found out of the tables of applied loads. Using the tables of applied loads is only a pre-measurment which does not replace a structural analysis.
Introduction into DIN 18 807 trapezoidal profile used for building construction
Should you require personal advice or do you have any special requirements, please feel free to contact us.